HB 0-51-1983 緊固件和定位銷孔中心距公差

Fastener and Dowel Hole Center Distance Tolerance

DIN 2769 E:2020-09 幾何產品規范（GPS） 一般公差 幾何公差和線性和角度尺寸公差的表格值 沒有單獨的公差指示

Geometrical product specification (GPS) - General tolerances - Tabulated values for geometrical tolerances and tolerances for linear and angular sizes without individual tolerance indication

DIN 2769:2021 幾何產品規范（GPS） 一般公差 幾何公差和線性和角度尺寸公差的表格值，沒有單獨的公差指示

This document specifies general tolerance values in tolerance classes for general geometrical and dimensional specifications as a supplement to DIN EN

Geometrical product specification (GPS) - General tolerances - Tabulated values for geometrical tolerances and tolerances for linear and angular sizes without individual tolerance indication

HB 0-51-1974 緊固件和定位銷孔中心距公差

Fastener and Dowel Hole Center Distance Tolerance

SANS 1700-4-3:2003 緊固件．第4部分：公差第2節：緊固件公差．螺栓，螺釘和螺母用平墊圈．A級和C級

Establishes a selection of tolerances for use in the preparation of ISO product standards for punched plain washers of product grades A and C for use

Fasteners Part 4: Tolerances Section 3: Tolerances for fasteners - Plain washers for bolts, screws and nuts - Product grades A and C

JJG 446-1986 931B型有效值差分電壓表檢定規程

Verification Regulation of Model 931 B RMS Differential Voltmeter

SFS 4011-1977 與工作方法有關的公差．削成碎片

Tolerances related to work methods. cut into pieces

SIS SMS 719-1959 固定零件，鉆孔，有凸緣固定鉆孔

Fixed parts, drilled holes, fixed drilled holes with flanges

UNI 7545-26:1994 危險標志的符號 跌倒時有高度差

Contiene il simbolo grafico, prospetto con le dimensioni ed esempio di designazione

Symbols for danger signs. Fall with difference in level.

NF M03-051:2002 固體礦物燃料.差值計算氧含量

Solid mineral fuels - Calculation of oxygen content by difference

SIS SMS 2625-1970 滾動軸承．有平座的推力軸承．公差

Rolling bearings. Thrust benrings with flat seats. Tolerantes

JJG 726-1991 標準電感器檢定規程

Verification Regulation of Standard Inductors

SFS 4012-1979 與工作方法有關的公差．打孔技術

T?ss? standardissa esitet??n ty?tapakohtaiset toleranssit ter?srakenteiden ja yleisen koneenrakennuksen valssatuista ter?slevyist? valmistetuille

Tolerances related to work methods. Hole punching technology

CAN/CSA C22.2 No.60896-22-2017(R2022 固定式鉛酸電池 第22部分：閥控型 要求（采用 IEC 60896-22:2004 第一版 2004-02 加拿大有偏差）

CSA Preface This is the first edition of CAN/CSA-C22.2 No. 60896-22, Stationary lead-acid batteries - Part 22: Valve regulated types

Stationary lead-acid batteries - Part 22: Valve regulated types - Requirements (Adopted IEC 60896-22:2004, first edition, 2004-02, with Canadian deviations)

SFS 3393-1975 與工作方法有關的公差．焊接結構

Tolerances related to work methods. welded structure